• Welcome to the new SAOCA website. Already a member? Simply click Log In/Sign Up up and to the right and use your same username and password from the old site. If you've forgotten your password, please send an email to membership@sunbeamalpine.org for assistance.

    If you're new here, click Log In/Sign Up and enter your information. We'll approve your account as quickly as possible, typically in about 24 hours. If it takes longer, you were probably caught in our spam/scam filter.

    Enjoy.

Search results

  1. Andrew

    Rear Frame Rails

    Hi Guys, It has been way too long and I hope everyone is well. I am finally using my SolidWorks 3D software to help me with my S3. I am almost finished designing up the model of the Rear Frame Rails so that they can cut them with the CNC. I hope to make this as easy as possible to fabricate...
  2. Andrew

    Overdrive Gear Box

    It is hard to show but the right side of the splined shaft looks worn and miss-shaped. It may be just near the end part of the shaft. I will remove and inspect the tail shaft this weekend.
  3. Andrew

    Overdrive Gear Box

    Sounds good, I will give it a go and report back. Probably will not get to things again until next week.
  4. Andrew

    Overdrive Gear Box

    How gentle? She seems to be really fixed on there. Tap up trying to lift housing? Is it ok to try and open it at the seam (at the location of the balancing pipe) or should I drop down to the lower part of the housing in line with the Solinoid?
  5. Andrew

    Overdrive Gear Box

    The tail stock looks to have about 6 7/16 nuts holding it on. Is it just a matter of removing the nuts and loosening off the balancing pipe?
  6. Andrew

    Overdrive Gear Box

    Hi Barry, I will do that this afternoon. Thank you for the continued support. Pictures to follow. Andrew
  7. Andrew

    Overdrive Gear Box

    Well I guess this hoser is “Hosed” as stated above! This is the trans and this is how I have been hosed. Would this happen due to miss alignment or unbalanced prop shaft? I guess an overdrive is not in the cards after all of this. Thanks guys.
  8. Andrew

    Overdrive Gear Box

    I think I have found a problem with the SI trans. The rear spline looks worn on one side. Can our guys tell me what you think. Should or can it be replaced?
  9. Andrew

    Overdrive Gear Box

    Great stuff, I have an original warning light for a S3. This will be great, thanks Tom!
  10. Andrew

    Reverse light

    Will do, thanks for the note.
  11. Andrew

    Overdrive Gear Box

    This is a S3 and I am looking to install a complete SI Tran with Overdrive. Looking at my relay and the wiring diagram, I don’t see a warning light noted. The S3 & SIV I believe are wired dirrerently and show a warning light. I wonder if it is possible to include a warning light in the SI...
  12. Andrew

    Overdrive Gear Box

    Hi Tom, Is there any problem incorporating a warning light with the SI OD setup? I see the S3-SV had quite a different setup (wiring) and it used a warning light on the dash. Thanks, Andrew
  13. Andrew

    Reverse light

    Hi Michael Even better, I will do some hunting around. Thanks again Michael.
  14. Andrew

    Reverse light

    Looking to make them work with the shrouds similar to the originals. They will be a little different using these lamps as shown above but they should look good on the car. I will need to see how a sample comes out before I go ahead and make two of them. I will make them out of stainless. Do...
  15. Andrew

    Overdrive Gear Box

    Yes, for sure. I would love to see some pics of your setup. Thanks
  16. Andrew

    Overdrive Gear Box

    Found 2 relays, no sure what the difference is other that the double contact. Would it matter which one is used? Are all the switches the same for all SI to SV? Thanks Andrew
  17. Andrew

    Overdrive Gear Box

    Thanks, that is good info.
  18. Andrew

    Overdrive Gear Box

    Yes, I think I will make one. Any idea of the gauge of wire that should be used?
  19. Andrew

    Help restoring 1962 Alpine please - late series ll

    Hi Colin, Thank you for the note, I made the change so that I can receive private messages. I also gave you an email this morning. I found the Gas Cap surround but not the gas cap. I am sure it is kicking around, just need to open the right box. I am finding all kinds of goodies that I...
  20. Andrew

    Help restoring 1962 Alpine please - late series ll

    I am not sure about it being a SV dash board. I don't think the SV dash boards come with the heater controls labels and surround embossed into the dash like that. I think the S3 (plastic), SIV and SV (metal) had a name plate that covered then entire heater control surround. Looks like it may...
Top