• Welcome to the new SAOCA website. Already a member? Simply click Log In/Sign Up up and to the right and use your same username and password from the old site. If you've forgotten your password, please send an email to membership@sunbeamalpine.org for assistance.

    If you're new here, click Log In/Sign Up and enter your information. We'll approve your account as quickly as possible, typically in about 24 hours. If it takes longer, you were probably caught in our spam/scam filter.

    Enjoy.

Search results

  1. bobbo

    Parrish top seals

    Thanks Bill. Now back to the basement to try and get my side drafts working. GRRRRR
  2. bobbo

    Parrish top seals

    Thanks for your comments. I'll try the clear coat on the rear window, worked fine on my Nissan's plastic headlights. side window and front seal to windshield frame is what I need. Heading out on Sunday to the Ancaster British car show and parts swap ( largest parts swap in Ontario Canada )...
  3. bobbo

    Parrish top seals

    have just acquired a Parrish top for my SV, and looking forward to refinishing it and using it to extend the season. Any leads or suggestions for the side window seals and windshield seal would be very much appreciated. Thanks Bob
  4. bobbo

    Diff oil

    Warren, don't you have the access hole on the transmission tunnel, right hand side? Works great with funnel and hose.
  5. bobbo

    Door hinge renew

    Just to update. I used a hack saw today to cut the pin at the 2 thrust washer locations. Actually only cut through at one of the thrust washer locations as the pin was snapped in half at the other. One third of the pin fell out ( top of hinge ) and I proceeded to drill out the other 2 portions...
  6. bobbo

    Door hinge renew

    Sounds like I'll need to find a machine shop, if not some good hinges. Bob
  7. bobbo

    Door hinge renew

    Removal of the pin? Is it pressed in? Will heating the hinge allow it to be pressed out? Bob
  8. bobbo

    Door hinge renew

    Thank you to Dan and Mike. Dan, the thread Mike sent me to had your info on parts to procced with the repair. I should be able to locate bushings and rod locally. Removal of the pin? Is it pressed in? Will heating the hinge allow it to be pressed out? Bob
  9. bobbo

    Door hinge renew

    For my series V, driver's side. The upper door hinge is sloppy to the point that the door drops about 3/8 inch at the b post. Causing the door paint and b post paint to chip off. I'm looking for info on rebuilding hinges as I can only think this must be an issue with many of our cars. Thanks Bob
  10. bobbo

    Front caliper issue

    Removed the pistons today. Tried to pry out with a couple of flat screw drivers, but they would not budge. Padded the space between the two pistons and put the air nozzle to the fluid fitting opening. That popped them out for a good clean up with some 1500 wet/dry paper and brake cleaner, mostly...
  11. bobbo

    Front caliper issue

    Pulled the caliper off again today. Pistons were a little easier to depress with the c-clamp. Re-installed and I can now rotate the wheel by hand, but still snug. I've ordered new flex lines for the front as I felt the old ones were hard to push fluid through, so probably swelling. This will...
  12. bobbo

    Front end Alignment

    In reply to Bill and ASM, yes hard to tell if front wheels are aligned with the rear. With my steering wheel centered in straight ahead, the Left front wheel seems to be in line, with the Right wheel pointing out away from the front. Until I get the car mobile I can't say if when driving...
  13. bobbo

    Front end Alignment

    great Hagerty article. Have square tube and welder. new weekend project in the works. Thanks, Bob
  14. bobbo

    Front caliper issue

    Bleeder , is open and the bleed passage is clear. I'm taking it off again on Friday and will try again with the c-clamp. It seemed to want to push back when I was using the c-clamp before, like it was under pressure.
  15. bobbo

    Front caliper issue

    Installing new flex lines for the front calipers on my SV. Had the calipers off to clean and check over. All seems good except the right caliper wont relax enough to allow free rotation of the wheel. No fluid in the system now so no hydraulic pressure. Very hard to get the pistons back far...
  16. bobbo

    Front end Alignment

    Whew! Lots to consider. John, do you have any pic's of your alignment rig in use? Steve, sending a PM. Bob
  17. bobbo

    Front end Alignment

    Looked at the chapter on alignment in the WSM. Yes very specific. Was hoping to get somewhat close without the procedures noted. I don't expect any shops will have the blocks etc. to perform as well as shims required, but I'll check around. May have to trip down to NY if I can't find a shop...
  18. bobbo

    Front end Alignment

    With my front calipers off for checking and clean-up I decided to a little checking on the front toe-in toe-out situation. Have noticed the right wheel seemed to have excessive toe -out when steering is in a straight forward position. C clamped 2 angle iron pieces 32 inches long, one to each...
  19. bobbo

    Brakes

    Thanks fellas for your feed-back on my rear drums. Got back at them today and all is well. Adjustment went easy nothing siezed and Parking brake works also. Now to finish the front disks and flush system completely and refill. Cheers, Bob
  20. bobbo

    Brakes

    Opened up my rear drum brakes today. They don’t appear the same as the WSM shows on pages K1 12 and 13. Looking for the manual adjustment wheel. Shoes look fine, but need to get them moved out closer to the drum.
Top