jmb
Donation Time
Rust-free Series II Alpine that spend it's driving days in SoCal. Not a spot of rust on or inside panels (other than surface rust of course). I'll be posting more stuff as I dig parts out of storage, but here's what's ready to go:
Front L&R quarters from mid-wheel-well to headlight. Includes partial wheel well and valance below headlight. Some floor and lower firewall as they were cut inside frame rails. Right side has a small dent (~5 in) on the wheel arch. $250 each. I believe these will fit all Serieses?
[SOLD] Rear L&R quarter from door jamb to tail light. Includes full wheel well and rear valance below tail light (cut inside frame rail all the way). $300 each.
[SOLD] L&R rockers. Currently one piece of whole midsection of car left to right with X member, trans tunnel, etc. intact. Can cut to order. $50 each or whatever steel you need from this area.
[SOLD] L&R doors. Stripped down, solid. $150 each.
[SOLD] L&R door hinges - upper and lower for each side. Solid - no sag, play, etc. Includes mounting screws. $60 each set.
Front valance section from hood hinges all the way down. Section between headlights. $25.
Rear valance section between tail lights. $25.
Hardtop. No dents, no glass. Mounting brackets are intact along with bottom trim bezel. No headliner, but liner bows are all there. $750.
Hood/Bonnet. Nice shape, not badging or other hardware. $200
Trunk/Boot lid. It's been a while, but I remember this had a bow in it, like someone tried closing the trunk with too much junk - seen this a lot with these and TRs. There are creases near the hinge mounts that need to straightened. Also a dent (pull-outable) where the license plate goes. No hardware. $150
Bumpers in original shape - would need rechrome, come with some bracketing. $200 each
Various sections of floor, frame, etc. Just ask. Had V8 so floor pans are not complete. $whatever
I also have the vent/cowl/top section that holds the bonnet latch and VIN and body tags (no tags with purchase as I don't believe they can be sold) from dash forward to engine compartment. Has cutout from V8 placement in the front of the vent box. $75
All prices are for pick up, we'll deal with shipping as needed.
Show interest in this post and we'll move over to PM as needed.
Front L&R quarters from mid-wheel-well to headlight. Includes partial wheel well and valance below headlight. Some floor and lower firewall as they were cut inside frame rails. Right side has a small dent (~5 in) on the wheel arch. $250 each. I believe these will fit all Serieses?
[SOLD] Rear L&R quarter from door jamb to tail light. Includes full wheel well and rear valance below tail light (cut inside frame rail all the way). $300 each.
[SOLD] L&R rockers. Currently one piece of whole midsection of car left to right with X member, trans tunnel, etc. intact. Can cut to order. $50 each or whatever steel you need from this area.
[SOLD] L&R doors. Stripped down, solid. $150 each.
[SOLD] L&R door hinges - upper and lower for each side. Solid - no sag, play, etc. Includes mounting screws. $60 each set.
Front valance section from hood hinges all the way down. Section between headlights. $25.
Rear valance section between tail lights. $25.
Hardtop. No dents, no glass. Mounting brackets are intact along with bottom trim bezel. No headliner, but liner bows are all there. $750.
Hood/Bonnet. Nice shape, not badging or other hardware. $200
Trunk/Boot lid. It's been a while, but I remember this had a bow in it, like someone tried closing the trunk with too much junk - seen this a lot with these and TRs. There are creases near the hinge mounts that need to straightened. Also a dent (pull-outable) where the license plate goes. No hardware. $150
Bumpers in original shape - would need rechrome, come with some bracketing. $200 each
Various sections of floor, frame, etc. Just ask. Had V8 so floor pans are not complete. $whatever
I also have the vent/cowl/top section that holds the bonnet latch and VIN and body tags (no tags with purchase as I don't believe they can be sold) from dash forward to engine compartment. Has cutout from V8 placement in the front of the vent box. $75
All prices are for pick up, we'll deal with shipping as needed.
Show interest in this post and we'll move over to PM as needed.
Last edited: